19.96CHF
ab 10 18.34CHF
ab 50 17.32CHF
ab 100 16.40CHF

NTE2114 IC MOS Static 4K RAM 300ns DIP-18

Bestell-Nr.:    NTE2114


Verfügbarkeit:     PICTURE_ONLY_ONE
  Sofort lieferbar!


NTE2114 NTE-2114 | ECG2114 ECG-2114 | NTE Electronics NTE2114
Integrated Circuit MOS, Static 4K RAM, 300ns

Description:
The NTE2114 1024-word 4-bit static random access memory is fabricated using N-channel silicon- gate technology. All internal circuits are fully static and therefore require no clocks or refreshing for operation. The data is read out nondestructively and has the same polarity as the input data. Common input/output pins are provided. The separate chip select input (CS) allows easy memory expansion by OR-tying individual devices to a data bus.

Features:
- All Inputs and Outputs Directly TTL Compatible
- Static Operation: No Clocks or Refreshing Required
- Low Power: 225mW Typ
- High Speed: Down to 300ns Access Time
- TRI-STATE Output for Bus interface
- Common Data In and Data Out Pins
- Single 5V Supply
- Standard 18-Lead DIP Package

Info as pdf-file
NTE-ECG replacement list as pdf-file
NTE-ECG diagrams

Absolute Maximum Ratings:
Voltage at Any Pin.......................................................... -0.5V to +7V
Power Dissipation, PD.............................................................. 1W
Storage Temperature Range, Tstg.......................................... -65° to +150°C
Lead Temperature (During Soldering, 10sec), TL.................................... +300°C

Functional Description:
Two pins control the operation of the NTE2114. Chip Select (CS) enables write and read operations and controls TRI-STATING of the data-output buffer. Write Enable (WE) chooses between READ and WRITE modes and also controls output TRI-STATING. The truth table details the states produced by combinations of the CS and WE controls.
During READ-cycle timing, WE is kept high. Independent of CS, any change in address code causes new data to be fetched and brought to the output buffer. CS must be low, however, for the output buffer to be enabled and transfer the data to the output pin.
Address access time, tA, is the time required for an address change to produce new data at the output pin, assuming CS has enabled the output buffer prior to data arrival. Chip Select-to-output delay, tCO, is the time required for CS to enable the output buffer and transfer previously fetched data to the output-pin. Operation with CS continuously held low is permissible.
Writing occurs only during the time both CS and WE are low. Minimum write pulse width, tWP, refers to this simultaneous low region. Data set-up and hold times are measured with respect to whichever control first rises. Successive write operations may be performed with CS continuously held low. WE then is used to terminate WRITE between address changes. Alternatively, WE may be held low for successive WRITES and CS used for WRITE interruption between address change.
In any event, either WE or CS (or both) must be high during address transitions to prevent erroneous WRITE.


Unser Halbleiter Katalog (ohne NTE-Sortiment)
NTE Sortiment (unser ganzes Sortiment)
Einzel-Halbleiter (ganzes Sortiment)

Fehler und Änderungen bei technischen Daten, Abmessungen und Preisen bleiben vorbehalten. Bild kann vom Original abweichen.
Hat sich ein Fehler eingeschlichen? Bitte hier melden


Suchen Sie nach einem Ersatztypen?

Anmerkung zu den NTE/ECG Austauschhalbleiter:
NTE-Austauschhalbleiter (früher ECG Philips und Sylvania) sind sorgfältig ausgesuchte und erprobte Halbleiter, die einen sicheren Ersatz für Originaltypen verschiedenster Hersteller und Ursprünge für fast alle Applikationsbereiche im Wartungsdienst bieten.
Alle NTE-Austausch-Halbleiter sind einzeln in durchsichtigen Plastikbeuteln verpackt, auf welchen die wichtigsten Daten vermerkt sind.
Anzahl:
Bewertungen

Kunden, die dieses Produkt gekauft haben, haben auch folgende Produkte gekauft:
Schnellsuche
1 x Arbitrary Funktionsgenerator 1μHz - 30MHz
1 x 4mm-Polklemme/Buchse schwarz 6A 60VDC
1 x Draht-Widerstand 2.7k 4W Tol=5%
1 x Impulsuebertrager 1zu10 Prim=15.5R Sek=180R
1 x Gluehlampe 48V 3W (13x30mm) E14 Roehrenform
1 x Korund-Schleifstein 22x3.5mm
1 x Markierungsring blau passend zu XLR Serie X
1 x Leistungs-Metallfilm-Widerstand 680R 2W Tol=5%
1 x Plastiktuelle gruen passend zu Klinkenstecker Serie C
1 x Draht-Widerstand 180R 1W Tol=10%
1 x 4A SCR Thyristor 600V TO-202 Typ X0403NE
1 x Print-Transformator 1.2VA Prim=230VAC Sek=24V 50mA
1 x LED-Pfeil mit Lauflichteffekt (Bausatz)
1 x Gluehlampe 5V 115mA (L=9.1mm) SX3 SMF Special Midget Flange
1 x Gluehlampe 6V 5W (14x25mm) Ba9s Kugelform
1 x BNC-Buchse Female/Female Flansch UG414A/U 50-Ohm
1 x Klinken-Kabelstecker 3.5mm 3-pol stereo Metall, RoHS
1 x Draht-Widerstand 3.3R 1W Tol=10%
1 x Batteriehalter 10x AA/AM3/UM3/Mignon/R6 Flach mit Lötanschl
1 x Draht-Widerstand mit Abgriffschelle 27R 100W Tol=10%
1 x Unabgeschirmte Buchse fuer Snap-In-Montage DIN 45327
1 x Metallfilm-Widerstand 4.32M 0.6W Tol=1%
1 x Gummidichtkappe IP65 Neutrik SCD-W
1 x Halbleitermodul passend zu SRS.G12.10AC OMRON G32A-A10-VD
1 x Digitaler FI Tester fuer Ausl&oesecharakteristik PeakTech 2710
1 x SMB-Einbaukabelstecker Crimpen Telegaertner J01160A0101
1 x Druckschalter-Taster EIN-EIN oder TAST 18x24mm th25
1 x Metallfilm-Widerstand 5.36M 0.6W Tol=1%
1 x Schaltnetzteil 85-264VAC 5VDC/3A 15W fuer DIN-Scienen Montage
1 x Gluehlampe 5V (L=11.4mm) T7/8 SX3 SMF Special Midget Flange
1 x Aluminium-Gehaeuse 160x86x37mm schwarz IP65 TEKAM-23.9
1 x Draht-Widerstand mit Abgriffschelle 8.2R 40W Tol=10%
1 x Gluehlampe 24V 5W (16x54mm) E14 Roehrenform
1 x Draht-Widerstand 33R 1W Tol=10%
1 x DIL-Codierkippschalter 6 Schalter 17.3mm OMRON A6D
1 x Print-Transformator 7.5VA Prim=230VAC Sek=15V 500mA
1 x 10mm LED weiss 8000mcd
1 x NTE7052 IC Mono BTL Audio Amplifier 3W SIP-9
1 x Schaltnetzteil 5VDC 6.5A 60W für DIN-Schienen, RoHS2
1 x Schaltnetzteil 48VDC 0.75A 30W für DIN-Schienen, RoHS2
1 x Schaltlitze DESCAFLEX T-70 (LiY) 0.50mm2 blau 100m
1 x Batteriehalter Printmontage vertikal fuer CR2450N und CR2477N
1 x Halogen Gluehlampe 22.8V 75W (10x63mm) R7s
1 x Transformator 150VA Prim=230VAC Sek=36V 4.17A
1 x DFG Bistabiles Miniatur-Relais 12V 2x Umschalter 220VAC 5A 100W
1 x Dual Low Operational Amplifier PDIP-14 Type TBA231 oder uA739PC
1 x Backofenlampe 230V 25W 300oC (25x56mm) E14 Philips 078.6010
1 x Professional Dual Typ-K-/IR-Thermometer PeakTech 5045
1 x Draht-Widerstand in Alugehaeuse 4.7k 25W Tol=5%
1 x Schaltnetzteil 24VDC 1.25A 30W FRIWO FW8030/24
1 x Trimm-Potentiometer 10mm horizontal 2.2k Tol=20%
1 x ISDN-Adapter schwarz T+T89 RJ45 8/4 (FCC 8/4)
1 x Trimm-Potentiometer horizontal 220R 0.5W
1 x Draht-Widerstand 2.2k 11W Tol=5%
1 x Batteriehalter Printmontage horizontal fuer CR2450N und CR2477N
1 x Buchsen-Schraubklemmleiste natur 1.5mm2
1 x Elko radial 2200uF 16V 13x20mm RM=5mm
1 x TNC-Kupplung Female/Female 50-Ohm
1 x Pfeil rot passend zu MAB.10xx
1 x Neutrik Mikrofonkabel 2x0.22mm2 gruen
1 x Transformator 50VA Prim=230VAC Sek=9.5V 5.26A
1 x Schaltlitze H05V-K (LiY) 0.14mm2 gelb 100m, RoHS
1 x Wippenschalter Ein-Aus Gruen 2-Pol DPST Marquardt 1805.7109
1 x Antennenstecker schraubbar gewinkelt Kunststoff
1 x Printrelais 12VDC 1U 16A 250VAC Finder Serie 41.61
1 x EPROM 1024x8 450ns DIP-24 Wide Type MM2708
1 x Folienkondensatoren Y1 MKP 20% 3n3 /500VAC RM=15mm
1 x NiCd-Akku 1.27 2400mAh SUB-C-Zelle mit Loetfahnen
1 x Zener Diode 1.3W 68V Typ BZX85C68
1 x NiCd-Akku 1.2V 4000mAh mit Loetfahnen, BlackFox
1 x HSS-Stahl-Spiralbohrer 0.8mm
1 x Transformator 25VA Prim=230VAC Sek=24V 1A
1 x Konstantstrom-Schaltnetzteil 60W Out: 500...1400mA waehlbar
1 x 16-Key Encoder PDIP-18 Type MM74C922N
1 x Auto Switchbox IEEE-1284 4zu1 parallel
1 x Metallfilm-Widerstand 25.5k 0.6W Tol=1%
1 x Cermet-Potentiometer 470k 5W 10%
2568.19CHF
Hersteller
Hersteller Info
andere Produkte
Sprachen
English Deutsch
Währungen