NTE2020 IC 8−Channel Darlington Array/Driver

Formerly: ECG2020

Integrated Circuit 8−Channel Darlington Array/Driver

See also >>> NTE2016, NTE2017, NTE2018, NTE2019

Description:
Ideally suited for interfacing between low−level digital logic circuitry and high−power peripheral loads, the NTE2011 through NTE2015 are high−voltage, high−current Darlington arrays in an 18−Lead DIP type package and feature peak load current ratings to 600mA (NTE2016, NTE2019) or 750mA (NTE2017, NTE2018, NTE2020) for each of the eight drivers in each device. Under the proper conditions, high−power loads up to 4A at 50V (200W at 23% duty cycle) or 3.2A at 95V (304W at 33% duty cycle) can be controlled. Typical loads include relays, solenoids, stepping motors, multiplexed LED and incadescent displays, and heaters. All devices feature open collector outputs and integral diodes for inductive load transient suppression.
The NTE2016 is a general purpose array that may be used with standard bi−polar digital logic using external current limiting, or with most PMOS or CMOS directly. This device is pinned with outputs opposite inputs to facilitate printed wiring board layouts.
The NTE2017 is designed for use with 14V to 25V PMOS devices. Each input has a Zener diode and resistor in series to limit the input current to a safe value in that application. The Zener diode also gives this deVicee excellent noise immunity.
The NTE2018 has a 2.7kΩ series base resistor for each Darlington pair, allowing operation directly with TTL or CMOS operating at a supply voltage of 5V. This device will handle numerous interface needs − particularly those beyond the capabilities of standard logic buffers.
The NTE2019 has a 10.5kΩ series input resistor that permits operation directly from CMOS or PMOS outputs utilizing supply voltages of 6V to 15V. The required input current is below that of the NTE2018, while the required input voltage is less than that required by the NTE2017.
The NTE2020 is designed for use with standard TTL and Schottky TTL, with which higher output currents are required and loading of the logic output is not a concern. This device will sink a minimum of 350mA when driven from a “totem pole” logic output.

Info as pdf-file
NTE-ECG replacement list as pdf-file
NTE-ECG diagrams

Absolute Maximum Ratings: (TA = +25°C for any one Darlington pair unless otherwise specified)
Output Voltage, VCE................................................................ 50V
Input Voltage, VIN
NTE2017, NTE2018, NTE2019................................................ 30V
NTE2020.................................................................... 15V
Continuous Collector Current. IC
NTE2016, NTE2019.......................................................500mA
NTE2017, NTE2018, NTE2020.............................................600mA
Continuous Base Current, IB.......................................................25mA
Power Dissipation, PD
One Darlington Pair.......................................................... 1W
Total Device (Note 2).......................................................2.25W
Operating Ambient Temperature Range, TA...................................−20° to +85°C
Storage Temperature Range, Tstg.......................................... −55° to +150°C

Note 1. NTE2017 is a discontinued device and no longer available.
Note 2. Derate at the rate of 18.18mW/°C above +25°C.
Note 3. Under normal operating conditions, these devices will sustain 350mA per output with VCE(sat) = 1.6V at +50°C with a pulse width of 20ms and a duty cycle of 40%.


Unser Halbleiter Katalog (ohne NTE-Sortiment)
NTE Sortiment (unser ganzes Sortiment)
Einzel-Halbleiter (ganzes Sortiment)

Fehler und Änderungen bei technischen Daten, Abmessungen und Preisen bleiben vorbehalten. Bild kann vom Original abweichen.
Hat sich ein Fehler eingeschlichen? Bitte hier melden


Suchen Sie nach einem Ersatztypen?

Anmerkung zu den NTE/ECG Austauschhalbleiter:
NTE-Austauschhalbleiter (früher ECG Philips und Sylvania) sind sorgfältig ausgesuchte und erprobte Halbleiter, die einen sicheren Ersatz für Originaltypen verschiedenster Hersteller und Ursprünge für fast alle Applikationsbereiche im Wartungsdienst bieten.
Alle NTE-Austausch-Halbleiter sind einzeln in durchsichtigen Plastikbeuteln verpackt, auf welchen die wichtigsten Daten vermerkt sind.