NTE978
Integrated Circuit Dual Timer
14-PIN DIP+
Info als pdf File
To order >>> NTE978C (CMOS 14-PIN DIP)
To order >>> NTE978SM (14-SOIC)
Description:
The NTE978 series dual timing circuit is a highly stable controller capable of producing accurate time
delays or oscillation. The NTE978 is a dual NTE955. Timing is provided by an external resistor and
capacitor for each timing function. The two timers operate independently of each other sharing only
VCC and GND. The circuits may be triggered and reset on falling waveforms. The output structures
may sink or source 200mA.
Features:
- Direct Replacement for 556 Timers
- Replaces Two 555 Timers
- Timing from Microseconds through Hours
- Operates in both Astable and Monostable Modes
- Adjustable Duty Cycle
- Output can Source or Sink 200mA
- Output and Supply TTL Compatible
- Temperature Stability better than 0.005% per °C
- Normally On and Normally Off Output
- Available in Three Types:
NTE978 14-Lead DIP
NTE978C 14-Lead DIP (CMOS)
NTE978SM SOIC-14 (Surface Mount)
Applications:
- Precision Timing
- Pulse Generation
- Sequential Timing
- Time Delay Generation
- Pulse Width Modulation
- Pulse Position Modulation
- Linear Ramp Generator
Absolute Maximum Ratings:
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +18V
Power Dissipation (Note 1), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1620mW
Operating Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C
Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65° to +150°C
Lead Temperature (During Soldering, 10sec Max), TL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +260°C
Note 1. For operating at elevated temperaturesthe device must be derated based on a +150°C maximum
junction temperature and a thermal resistance of +77°C/W for NTE978 and NTE978C
and +110°C/W for NTE978SM.
Note 2. Supply current when output high typically 1mA less at VCC = 5V.
Note 3. Tested at VCC = 5V and VCC = 15V.
Note 4. As reset voltage lowers, timing is inhibited and then the output goes low.
Note 5. This will determine the maximum value of RA + RB for 15V operation. The maximum total
(RA + RB) is 20MΩ.
Note 6. No protection against excessive Pin1, Pin13 current is necessary providing the package dissipation
rating will not be exceeded.
Note 7. Matching characteristics refer to, the difference between performance characteristics of
each timer section.
Fehler und Änderungen bei technischen Daten, Abmessungen und Preisen bleiben vorbehalten. Bild kann vom Original abweichen.
Hat sich ein Fehler eingeschlichen?
Bitte hier melden
Suchen Sie nach einem Ersatztypen?
Wir führen die NTE Austausch-Halbleiter in unserem Sortiment
Anmerkung zu den NTE/ECG Austauschhalbleiter:
NTE-Austauschhalbleiter (früher ECG Philips und Sylvania) sind sorgfältig
ausgesuchte und erprobte Halbleiter, die einen sicheren Ersatz
für Originaltypen verschiedenster Hersteller und Ursprünge für
fast alle Applikationsbereiche im Wartungsdienst bieten.
Alle NTE-Austausch-Halbleiter sind einzeln in durchsichtigen
Plastikbeuteln verpackt, auf welchen die wichtigsten Daten
vermerkt sind.
Sprachen integrierter Schaltkreis integrated circuit, kurz IC, Mikrochip Microchip integreret kredsløb integreret kredslob circuito integrado (CI) circuit intégré (CI) circuit integre (CI) circuito integrato geïntegreerde schakeling geintegreerde schakeling Tümdevre Tuemdevre